Sherwood rvd - 6095r manual


















These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FOR U. Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel.

Refer to the following paragraph for the proper setting of this switch. Observe all safety precautions with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped.

Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth.

Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. When making connections between components, please be sure to connect the white RCA plugs to the L left and the red RCA plugs to the R right jacks respectively.

Change the position of the FM indoor antenna until you get the best possible reception of your favorite FM stations. A 75 ohm outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before connecting the outdoor antenna. Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set if to a direction it to a for the best reception.

Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. If the electricity fails or the AC input cord is left unplugged for more than 2 weeks, the memorized contents will be cleared. Should this happen, memorize them again. Confidential Unpublished Works. All rights reserved. US Pat. Copyright Digital Theater System, Inc.

All Rights Reserved. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. For details, see the operator's manual of the component to be connected. Use these jacks when adding additional amplifiers. Center speaker: Place the center speaker either above or below the TV set to assure good visualization of center channel program.

Rear speakers: Place the rear speakers approximately 1m above the ear level of a seated listener on the direct left and right of them or slightly behind.

Subwoofer: Reproduces powerful deep bass sounds. Place a powered subwoofer anywhere in the front as desired. The ideal surround system needs all the speakers listed above. To accurately reproduce DTS digital surround, center and rear speakers as well as front sperkers should be full range speakers. TONE D. USER - for adjusting equalizer pattern as desired. FILE - for selecting desired equalizer pattern in the preset or in the user mode. MON - for monitoring the sound of recording or playback on tape deck.

For selecting a track or a disc in CD mode. When selecting a disc, select disc No. Notes: Some functions for CD players, tape decks or equalizer may not be operable from the remote control. For details about functions, refer to the operating instructions of each component.

MON The operating range of the remote control is about 23 feet 7 Meters and it will operate at angles of up to 30 degrees. Aim the remote at the remote sensor. Do not use rechargeable batteries Ni-Cd type. This circuitry works by redirecting the bass frequencies or the entire channel to speakers that are capable of reproducing them. When a large or full range speaker capable of deep bass response is used for one of the channels, that channel should be set to L. When a small or satellite speaker with limited bass capability is used, that channel should be set to S.

Deep bass from that channel will be redirected to the main left and right speakers or to the subwoofer. When there is no speaker available, that channel should be set to N. All the information in that channel will be redirected to other available speakers.

The existing front-rear-center speaker setting is displayed. Your requested speaker settings are entered into memory and the set-up procedure advances to the subwoofer mode. Each time this button is pressed briefly, the frontcenter-rear speaker or subwoofer setting is displayed.

Adjust the level of the selected channel as desired. Engage the Test Tone mode by pressing the Test Tone button on the remote control. This can help focus the audio image and add enjoyment to your home theater experience. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction. AC voltage selector switch Move switch lever to match your line voltage with a small screwdriver or other pointed tool.

Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

Confidential Unpublished Works. All rights reserved. For details, see the operator's manual of the component to be connected. Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. A 75 outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one.

Point it in the direction that offers the best reception. Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. If the electricity fails or the AC input cord is left unplugged for about 2 weeks, the memorized contents will be cleared.

Should this happen, memorize them again. Yourn new high fidelity receiver is designed to deliver. Please take a few moments to read this manual. It will explain the features and operation of. We recommend that. They will be. Your unit. To avoid damage, never place the unit near radiators, in. Connect your complementary. This symbol is intended to alert the user to the. To reduce the risk of fire or electric shock, do not expose.

This equipment has been tested and found to. These limits. This equipment generates, uses and can. However, there is no guarantee that interference will. Your unit is designed to be placed in a horizontal position and it is important to allow at least two inches of space behind your unit for adequate ventilation and cabling convenience. To avoid damage, never place the unit near radiators, in front of heating vents, in direct sunlight, or in excessively humid or dusty locations.

Connect your complementary components as illustrated in the following section. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance.

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Caution : Do not block ventilation openings or stack other equipment on the top. Note to CATV System Installer: This reminder is provided to call the CATV system installer's attention to Article of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:.

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Units shipped to the U. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe.

For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician. Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel.

Refer to the following paragraph for the proper setting of this switch. This unit operates on V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage.



0コメント

  • 1000 / 1000